PLC Archives - CS Electrical & Electronics

All Questions › Tag: PLC

Filter:All Open Resolved Closed Unanswered
What would be the resolution value if oscillator and PWM frequencies are 16MHz and 2 MHz respectively?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
466 views1 answers0 votes
How do the variations in an average value get affected by PWM period?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
647 views1 answers1 votes
What is the status of shift clock supply in an USART synchronous mode?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
323 views1 answers0 votes
Which bit plays a salient role in defining the master or slave mode in TXSTA register especially in synchronous mode?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
303 views1 answers0 votes
Which register/s should set the SPEN bit in order to configure RC7/RX/DT pins as DT (data lines)?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
231 views1 answers0 votes
Which among the below assertions represent the salient features of PIC in C-18 compi
AnsweredJayesh Bornare asked 3 years ago • Embedded System
317 views1 answers0 votes
Which command-line option of compiler exhibits the banner comprising overall number of errors, messages, warnings and version number after an accomplishment of the compilation process?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
302 views1 answers0 votes
In which aspects do the output functions specified in stdio.h differ from ANSI specified versions?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
465 views1 answers0 votes
What does the 'program idata' section of data memory contain in C-18 Compiler?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
332 views1 answers0 votes
Where is the result stored after an execution of increment and decrement operations over the special – purpose registers in PIC?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
483 views1 answers0 votes
Which instruction is applicable to set any bit while performing bitwise operation settin
OpenJayesh Bornare asked 3 years ago • Embedded System
232 views0 answers0 votes
Which flags of status register are most likely to get affected by the single-cycle increment and decrement instructions?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
249 views1 answers0 votes
Which bit permits to enable (if set) or disable (if cleared) all the interrupts in an INTCON
AnsweredJayesh Bornare asked 3 years ago • Embedded System
352 views1 answers0 votes
The RPO status register bit has the potential to determine the effective address of____
AnsweredJayesh Bornare asked 3 years ago • Embedded System
285 views1 answers-1 votes
Which bit/s should be necessarily cleared in OPTION (SFR) register in order to turn on the weak internal pull-ups of port B?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
477 views1 answers-1 votes
What is the purpose of acquiring two different bits from INTCON register for performing any interrupt operation in PIC 16C61 / 71?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
285 views1 answers0 votes
What is the purpose of a special function register SPBRG in USART?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
313 views2 answers0 votes
Which register acts as an input-output control as well as data direction register for PORTA in bank 2 of RFS?
AnsweredJayesh Bornare asked 3 years ago • Embedded System
249 views1 answers0 votes

Share Now